Cracked Driveway: Find the Right Repair Technique for Asphalt to Restore Your Home’s Curb

Replacing your entire asphalt driveway is an expensive project to undergo. Rather than let your driveway fall apart as it erodes over time, you can use the right technique to repair it. In this article, we’ll be exploring the best approach you can use to restore the asphalt of your home’s curb. Keep in mind that while this is a relatively straightforward procedure, the rain could ruin your hard work. However, you could skip the logistics of asphalt repair entirely by hiring a local cleaning business like JC Eco Blasting. Now let’s get started:

  • Buy Your Materials

If you’re attempting to fix your asphalt for the first time, no doubt your question is what you’ll need. Knowing what you need before starting the project will prevent you from running last-minute trips to the store. The materials you’ll need for the project are asphalt crack filler, patch material, primer, sealer or trowel patch, and a foam backer rod. These items are all essential is restoring your home curb, as you’ll see below.

Tools you need to have for the task are an air compressor, circular saw, stiff push broom, scrub brush, and a shovel. You might also find a lawn edger useful, but it’s not necessary.

  • Prep Your Driveway

After getting the right tools and materials, the first to do is prep your driveway for the project. Cleaning your driveway before you start will save you a lot of time and energy later. So don’t skip this step. Start by removing stray leaves, acorns, and dust from your curb. The asphalt primer comes in handy in removing oil stains before you commence sealing. If there are weeds embedded in the asphalt cracks, you’ll need to take those out too. It’s hard and unpleasant to remove moss with your hand, so try using a pressure washer to get it out. A spray bottle with a mix of bleach and water is an alternative substitute for a pressure washer. Use a scraper to remove it from the surface.

Note that you’ll have to wait for it to dry after cleaning the driveway before proceeding with the next step altogether. Hence the reason you should pay attention to the weather forecast.

  • Patch up the Cracks

Once the driveway is dry, you can now patch up the cracks and holes. You’ll be able to pour a more uniform layer of sealant if you fill the cracks first. You may have to use a diamond wheel to drag out any old filler and widen the gap first. Then you can proceed to fill the holes with your asphalt filler.

Be careful not to overfill the holes, so you don’t make the patches visible after applying the sealant. You can use a scraper to get it out if you accidentally overload. Most asphalt crack fillers have self-leveling properties, but if yours doesn’t, then you can use a torch flame. Move it from side to side until the filling melts, and repeat.

  • Add the Sealant

After patching up all the holes on the curb, you’re ready to add your sealant. Before starting, clean the driveway one more time, to be sure it’s completely free from dust and debris.  Just a quick sweep with a broom or leaf blower should do the trick. Avoid mixing all the buckets of sealant you have at once. Mix each bucket just before applying it to your driveway.

Don’t back yourself into a tight spot as you apply the sealant. You can always use a paintbrush to finish the edges. You can use a squeegee or stiff push broom for most of the driveway to spread the sealant evenly. However, you might still want to use a brush to seal the edges. Pay attention to the amount of trowel mix you apply as you work, avoid adding too much in some areas, and leave others bare. Allow the driveway to dry for at least 24 hours.

  • Throw on a Second Coat

It’s possible to find you made mistakes, even after taking the utmost precautions. If you have an old driveway, some areas will need another coat, so apply a second coat of coolant. Not only will this increase the evenness of your curb, but it’ll also provide an extra layer of protection for the surface. It would be best if you let the driveway dry for another 24 hours before using it. To be on the safe side, allow an extra day or two passes before driving on it.

Conclusion

To increase the lifespan of your newly repaired asphalt driveway, you should endeavor to fill the cracks and restore the edges every year. You can space the process of applying a new coat of sealant by four to five years. Following directions is vital in restoring your home’s curb. You could always leave the job to the pros, to examine, estimate cost, and repair your asphalt driveway.

About RJ Frometa

Head Honcho, Editor in Chief and writer here on VENTS. I don't like walking on the beach, but I love playing the guitar and geeking out about music. I am also a movie maniac and 6 hours sleeper.

Check Also

patio table and chair set on a garden

Melbourne outdoor furniture

Having a fancy outdoor living space is the inclusion of natural beauty in your life. …

Leave a Reply

Your email address will not be published. Required fields are marked *

This site uses Akismet to reduce spam. Learn how your comment data is processed.